DwyerOmegaDP7600-Series
DP7600-A10-DC9/18
High Speed Load/Strain Meters and Process/Voltmeters, Dual Differential Inputs Available
- 판매 가격
- 가격 문의
수량
재고: 0개국내 재고가 없어도 주문 가능합니다. 주문 시 해외 재고를 확인합니다.
무료 배송 10만원 이상
납기: 35 weeks리드타임은 상황에 따라 달라질 수 있습니다.
연구비카드 사용가능
실시간 문의하기제품 사양
Brand:OMEGA Engineering
Accuracy:± 0.01 %
Accuracy Detail:± 0.01% of reading ± 1 count of A/D @ 25°C (77°F)
Bridge Resistance:100 to 5000 Ω
Bridge Resistance Note:100 to 5000 Ω; 4-wire or 6-wire configuration
Calibration Note:Shunt calibration capability with span programmable from front panel; no potentiometer adjustments; access code prevents unauthorized calibration switches
Channels:One channel standard, second channel optional
Coarse Gain Setting:Selectable by rear switches
Control Output:N/A
Convert/Hold Input:Normally high; if pulled low, holds display
Cutout Dimensions:2.45 x 5.06 in
Data Interface:N/A
Digital Filter:Programmable Cutoff Frequency
Display Note:-32768 to 32767 with programmable decimal points; 14 mm (0.56") red LED
Display Type:LED
Electrical Connection:Screw Terminal
Electrical Output:0 to 10 Vdc
Form factor:1/8 DIN
Height:2.7 in
Input Analog Filter:4-pole active anti-alias; 500 Hz cutoff on single-channel unit and 250 Hz cutoff on dual-channel unit
Input Bias Current:± 50 nA maximum ± 100 pA/°C (per input channel)
Input Configuration:Front Keypad
Input Type:Strain
Internal Resolution:16 bit
Length:6.9 in
Materials:Porcelain
Measurement Type:Current, Strain, Voltage
Mounting:Panel
Number of Digits:5
Number of Inputs:1
Operating Temperature, Max:60 °C
Operating Temperature, Min:-20 °C
Output Detail:Analog Output: 0 to 10 Vdc; tracks display reading; voltage outputs will sink or source 1 mA; 300V isolation between analog outputs and instrument ground
Output Method:RJ11 jack for serial interface
Output Signal:Voltage
Peak Detection:Updated at rate selected by digital filter, peak stored in memoryrogrammed to give limit #1 output up to 100 seconds after a programmed limit is reached. This output can be used to reset the peak reading by tying limit #1 output to remote input
Power Consumption:8 W
Range Selection:Selectable by dip switch on rear of unit
Range Selection Note:5.1, 10.2, 15.3, 20.0, 26.3, 30.6, 35.1, 39.2 (in mV)
Reading Rate:Limited to 1000/s divided by number of channels
Remote Inputs:Display Peak, Display Runout, Reading, Reset Peak, Runout Reading, Tare
Resolution:16-bit A/D
Rollover Error:± 2 counts of A/D @ 25°C (77°F)
Runout Mode:Updated at rate selected by digital filter. Runout is normally stored in memory and recalled via front-panel switch, over the serial interface, or by selecting runout display mode on rear connector.
Sampling Rate:1000 Hz
Sensor Excitation:± 15 Vdc, ± 5 Vdc @ ± 50 mA
SetPoint Outputs:4 isolated open collector transistor outputs rated 30 Vdc maximum; will sink up to 50 mA; 300 V isolation between limit outputs and system ground; limit #1 can be programmed to be delayed from 1 to 100 seconds
Settable Parameters:Digital Filter, Limits, Offset, Span
Supply Power Note:9 to 18 Vdc @ 600 mA
Supply Power Type:DC
Supply Voltage:9 to 18 Vdc
Weight:370 g
Width:5.18 in
문서 및 매뉴얼